Components
Individual mounting components including adapter plates, ball adapters, tightening rings, and spare parts. Build or customise your mounting setup with Arkon's modular component range.
Showing 48 of 99 products
AP020
The AP020 90mm adhesive mounting disk allows you to mount an Arkon or third-party 80mm windshield suction mounting pedestal to your car’s dashboard, including mounting pedestals for Garmin and TomTom GPS devices.
AP4229P20B
Model AP4229P20B 90mm high performance adhesive mounting disk allows you to mount an Arkon or third-party 80mm windshield suction mount to your car or truck's dashboard, including mounts for Garmin and TomTom GPS devices. (Note that the disk is meant to be a bit larger than the mount to ensure a secure fit.)
APD2MAMPS20
The Diamond 2-Hole AMPS to 20mm adapter is a drill base product designed for tight locations and allows you to convert to any 20m pattern pedestal. The 20mm adapter is designed for Arkon’s HD Series. Including this adapter will complete your custom heavy-duty mount. Compatible with all 20mm ball mounts.
APM893M
Features: High-strength, weather-resistant VHB Adhesive Great accessory for suction mounts Secure your Magnetic Mount Base Semi-permanent solution Material: Metal
APMAMPS38MM
The APMAMPS38MM metal adapter converts your 38mm (1.5 inch) mount into a 4-Hole AMPS drill-base mount.
APVHB13
The APVHB13 80mm adhesive mounting disk features an extra-strength 3M VHB adhesive and allows you to securely mount an Arkon or third-party 70mm windshield suction mounting pedestal for smartphones and Garmin GPS to your car’s dashboard.
APVHB20
The APVHB20 90mm adhesive mounting disk features an extra-strength 3M VHB adhesive and allows you to securely mount an Arkon or third-party 80mm windshield suction mounting pedestal to your car’s dashboard.
CAQCFI
This fixed install charger also includes an LED indicator light and short circuit protection, and charges for up to 90 minutes after ignition is off. The charger includes an approximately 6-foot cable. It is strongly recommended that you have knowledge of your vehicle's operation before installing. Note: if using CAQCFI on electric forklifts with 36/48 Volt power, a voltage reducer (not included) should be used.
FLIFT01
FLIFT01 is designed for mounting and securing devices such as tablets, barcode scanners, radios, or other devices to a forklift, pallet jack, or other warehouse vehicle.
FLIFT02
FLIFT02 is designed for mounting and securing tablets, barcode scanners, radios, or other devices to a forklift, pallet jack, or other warehouse vehicle. Consisting of two steel plates with black powdercoat finish and accompanying mounting hardware, FLIFT02 is made with heavy gauge steel construction to last in tough environments, such as construction sites, factories, and warehouses.
GN01022VHB-B
This low-profile mount measures 1.25" high and can be adhered to any flat surface, including car dashboards or consoles, computer monitors, or table tops using the durable 3M VHB adhesive.
GN03122
The GN03122 clamp post mount is compatible with 22mm ball components. Use on a wheelchair rail, as a microphone stand mount, or on any handlebar or post measuring 12 to 40mm in diameter.
GPSHDCS7
. Compatible with 5 in. 6 in. and 7 in. GPS devices as well as selected 7 in. tablets and other accessories . Case measures 7.25 in. long x 4.5 in. wide x 1 in. thick . Use removable pad for 5 in. GPS devices . 2 year limited warranty provided by Arkon
HM009
The mounting plate measures 4.25 x 5.25 inches (108mm x 133mm), and features 4-Hole AMPS as well as other hole patterns to hold tablets, mobile printers, payment terminals, or other devices.
IBMAG2XHD8
The locations and scenarios you can live stream from are endless. Whether you're presenting at a conference, teaching in a class, or streaming live video from the home or office, the Dual Phone Magnetic Mount Stand is the must-have companion accessory for your Instagram, YouTube, or Facebook Live broadcasts.
MC25MMB
Specifications: Design: handlebar ring mount with 25mm ball end for mounting various holders and adapters to your vehicle's handlebars Model: MC25MMB Materials: Reinforced composite and aluminum Surface Mount Pattern: MC25MMB Ring mount up to 30mm (1.2") diameter plus three different adapter rings Included: 25mm ball end
MC2B
. Mount fits on handlebars measuring up to 31.75mm or 1.25 inches in diameter . Made of aluminum and is easy to install . Designed for use with Garmin nuvi GPS devices with 17mm swivel ball pattern . 2 year limited warranty
MC2C
. Mount fits on handlebars and poles 21.68mm to 30mm in diameter . Designed for use with Garmin GPS devices with 17mm ball pattern . Made of aluminum and is easy to install . Spacer rings included to ensure best fit . 2 year limited warranty
MC4B01B
The mount fits on handlebars measuring up to 30mm or 1.2 inches in diameter and is easy to install with the included hex key. Three handlebar spacer/adapter rings of different widths are also included with the mount to ensure a snug fit. Choose the appropriate size for optimum mounting to your handlebar. The mount swivels 360 degrees to position the device (not included) to your liking.
PPTAB1AMPS
Arkon's PPTAB1AMPS Slim-Grip Holder with 4-Hole AMPS Mounting Pattern is ideal for holding portable mobile printers, including those from Zebra, Epson, and Brother. The holder is compatible with most...
SP-1420-SCREW
Turn your standard camera mount or tripod into a GoPro-compatible accessory. This adapter is compatible with camera mounts, tripods, and other accessories with a 1/4”-20 mounting bolt.
SP-1420CAM
The SP-1420CAM adapter converts any mount or pedestal with a 17mm ball to a 1/4”-20 camera bolt pattern, making the mount compatible with DSLR or small action cameras.
SP-GN047-RVC-POM
These clips feature improved materials and are available in a set of 2. These air vent mount clips attach onto any horizontal car air vent louvers.
SP-GP-SCREW
. Replaces GoPro action camera lateral screw . Use with mounts and other mounting accessories with the GoPro lateral screw pattern . 2 year limited warranty
SP-RMSH-KIT
Arkon's SP-RMSH-KIT provides the hardware needed to replace the knob on one of Arkon's 25mm ball compatible Robust Shaft Arms. Arkon's Robust Mount Shaft Arms can be upgraded with security hardware to secure your device. Simply replace the shaft knob with the new screw, using the included hardware. This simple but effective substitution deters theft and provides a clean solution for your mount.
SP-SB-GPLAT
Mount your GoPro action camera to any 17mm ball mount with SP-SB-GPLAT.
SP-TABS5PK
. Available in set of 5 stoppers . Support stoppers keep Slim Grip tablet holder top and bottom support legs securely in place . For Arkon tablet holder Model TAB001 and corresponding mount bundles . 2 year limited warranty
SP-VHB25MM
. 70mm VHB mounting disk allows you to directly mount an Arkon Robust Mount or other third party 25mm mount . Extra strength adhesive mounting disk features 8 “petals” that bend to adhere to dashboards or slightly curved surfaces . 2 year limited warranty
SP02320
It fits easily into car or truck cup holders and the one-piece base twists to expand to fit cup holders up to 3.5 inches in diameter.
SP1420MAG
The heavy-duty magnetic base is perfect for use on surfaces where drilling or clamping is not ideal.
SP1420MAG25
The heavy-duty magnetic base is perfect for use on surfaces where drilling or clamping is not ideal.
SP25MM17
SP25MM17 is a versatile adapter that allows you to convert mounts with a 25mm (1 inch) mounting pattern (including Arkon Robust Mount models and RAM Mounts—sold separately) to a 17mm mounting pattern.
SP25MM25
Arkon’s SP25MM25 adapter allows you to connect and extend mounts and pedestals with a 25mm (1 inch) mounting pattern to other 25mm mounts.
SP25MMCAM
SP25MMCAM is compatible with cameras having the 1/4”-20 mounting pattern, and fits onto mounts accommodating the 25mm (1 inch) ball pattern (including Arkon Robust Mount models and RAM Mounts—sold separately).
SP25MMPL
. 25mm (1 inch) adapter extends to other 25mm ball pattern mounts and pedestals . Compatible with Arkon Robust Mounts or other mounts with 25mm ball pattern . Adapter fits onto 25mm mount head or base . 2 year limited warranty
SPAMPSMAG88
The heavy-duty magnetic base is perfect for use on surfaces where drilling or clamping is not ideal. The AMPS mount pattern consists of four holes located in a rectangular pattern spaced at 30.17mm by 38.05mm (measured as the center-to-center distance between holes).
SPCONDUIT
SPCONDUIT accompanies our seat rail and floor mount models to prevent vibration and unnecessary movement on the road. It can be attached to surfaces such as a car or truck consoles.
SPGP1420
Make your GoPro mount accessories compatible with the 1/4”-20 standard camera pattern with Arkon’s SPGP1420 adapter.
SPHD8BASE
SPHD8BASE is a weighted base that can be used with Arkon's Pro, Pro+Plus, and Cookie Decorator Stands. The base includes a collar for insertion of the pole used with Pro Stand models, including the Remarkable Creators Bundle (Model RCBTABLED) and Cookie Decorators Mount Stand for Phones and Pico Projectors (Model CDM2XMG5). SPHD8BASE measures approximately 7 inches wide by 7 inches long by 2.5 inches high (178 x 178 x 64mm), and weighs approximately 2 pounds, 14 ounces.
SPHD8L29
Extendable feature for customizable length High-quality materials for durability and reliability
SPHD8L29BP
Convert your Arkon Pro Clamp Phone or Camera Stand (Model CLAMPRV29) or Remarkable Creators Clamp Phone or Camera Stand (Model CLAMPRCB) clamp to a weighted base with SPHD8L29BP.
SPHD8L29CLAMP
Arkon's SPHD8L29CLAMP is a clamp base that can be used with Arkon's Pro Stand models.
SPHD8L29PINK
This aluminum extension pole is height adjustable from 17 inches to 29 inches tall. Stands and devices are not included. Simply remove the three-shaft arm assembly from the existing black pole, remove the pole from the base, then replace with the pink pole. Also available in teal (Model SPHD8L29TEAL).
SPHD8L29TEAL
This aluminum extension pole is height adjustable from 17 inches to 29 inches tall. Stands and devices are not included. Simply remove the three-shaft arm assembly from the existing black pole, remove the pole from the base, then replace with the teal pole. Thanks to our friends in the Chalk Couture Designer Community for inspiring this unique add-on. We were inspired to create this special edition extension pole to match the teal color used by them. Also available in pink (Model SPHD8L29PINK).
SPHDEXT
Add extra arm length when streaming live video using Arkon's Pro Stand Live Streaming Crafting or Cooking Mount (Model HD8RV29) with SPHDEXT. This bundle was created especially for current owners of the HD8RV29 Pro Stand who want to add additional arm length and flexibility for live streaming crafting or baking on Periscope, Facebook Live, Instagram or other apps.
SPHDMAGKIT
The mount's built-in magnet head powerfully attaches to the metal plate, keeping your smartphone or other device secure without using a holder.
SPRM023
. Features 25mm (1 inch) ball head . Compatible with Arkon and other third party device holders . Mount base twists to expand up to 3.5 inches in diameter . 2 year limited warranty
AP013
The AP013 80mm adhesive mounting disk allows you to mount an Arkon or third-party 70mm windshield suction mounting pedestal to your car’s dashboard, including Arkon’s mounting pedestal models GN079WD-SBH, GN068WD-SBH, GN022-SBH, GN014-SBH, GN015-SBH, and GN042-SBH.